Common Indoor Air Pollutants
CARBON MONOXIDE (CO)
Carbon monoxide is a colorless, odorless gas that can be fatal when breathed. Carbon
monoxide is produced by the incomplete combustion (burning) of fuels. This can occur
several ways:
- When flues or chimneys become blocked so exhaust cannot be vented to the outside.
- When a fuel-burning furnace has a cracked or rusted heat exchanger that allows combustion
gases into the living spaces.
- When fuel-burning space heaters (kerosene or gas), ovens, ranges, or grills are
operated in the home without adequate ventilation.
- When car exhaust from an attached garage enters the home.
Harmful
buildups of these gases can occur when exhaust from combustion equipment is not
vented to the outside of the home, and when combustion equipment is not in good
working order and is not regularly inspected for safe operation. Some homes may
also have a problem with “backdrafting.” That’s when the air pressure inside the
home is less than the air pressure outside the home, causing combustion by-products
from furnaces, water heaters, fireplaces, and similar equipment to spill back into
the room rather than being vented outside. Backdrafting can also occur when natural
draft appliance exhaust is pulled back into the house by mechanical ventilation
such as a down-draft kitchen power vent.
For more information, read EPA's Fact Sheet entitled Preventing Carbon Monoxide Poisoning – Information for Older
Adults and Their Caregivers.
Health Effects
Carbon monoxide is absorbed through the lungs into the blood where it interferes
with the blood’s ability to carry oxygen. At low levels it can cause fatigue in
healthy people and chest pain in people with heat disease. At higher levels, carbon
monoxide can cause headaches, dizziness, weakness, nausea, and confusion. Very high
levels can cause death.
Carbon monoxide symptoms can be similar to the flu. Carbon monoxide may be the problem
when you feel bad only when you are inside the home and the symptoms gradually disappear
after you have left, or if more than one person in the home has similar symptoms.
Control Methods
To reduce the risk from carbon monoxide keep all combustion equipment well-maintained
and inspected for safety. Experts recommend having your combustion heating systems
inspected by a trained professional every year. Such inspections should look for
blocked openings to flues and chimneys, cracked or disconnected flue pipe, signs
of soot around openings in your furnace or boiler, rust or cracks in the heat exchanger,
and exhaust or gas odors. Always operate combustion equipment for its intended use
and make sure it has been installed properly. Never use unvented combustion appliances
indoors (including space heaters), or use a gas stove for heating your house.
Carbon monoxide alarms can be installed which will alert you to dangerous levels
of this invisible gas. It is important to choose and place an alarm wisely and maintain
it to assure accurate sensing of carbon monoxide.
FORMALDEHYDE
Formaldehyde
is a colorless gas which has a distinctive, pungent odor at higher concentrations.
It has a number of useful properties, is a good preservative and products made with
formaldehyde make an excellent adhesive. It is widely used in some products in the
building and furniture industries and is also found in some textile products as
an anti-wrinkle agent.
Sources
Formaldehyde is released from some household products such as plywood, particleboard,
draperies, wallpaper, furniture fabrics, glues and adhesives, tobacco smoke, some
personal care products, and some foam insulation. As these materials age, they generally
stop releasing significant amounts of formaldehyde.
Health Effects
Short term, low-level exposure may cause temporary eye, nose, and throat irritation.
Some people may become more sensitive to formaldehyde after an initial exposure.
Control Methods
Formaldehyde exposure can be reduced by avoiding products that contain formaldehyde
or buying low-emitting formaldehyde products. Where new formaldehyde-containing
products have been installed, ventilation can be temporarily increased. High humidity
and high temperatures will increase the rate at which formaldehyde escapes from
materials. Air-conditioning and dehumidification may help to reduce formaldehyde.
RADON
Radon is a colorless, odorless gas that occurs naturally and is found everywhere
at varying low levels. Radon is constantly produced from the breakdown of uranium
in soil or rock.
Sources
Radon gas in the soil can enter homes through dirt floors, cracks in the basement
walls or floors, floor drains, or sumps. The churning of water in washers, showers,
toilets, and sinks releases radon gas into the air.
Health Effects
Exposure to elevated levels of radon increases the risk of lung cancer.
Control Methods
All homes should be tested for radon to know if there is a radon problem. If radon
levels are high, the problem is fixable. The cost depends on your home’s location,
construction, and levels of radon. The U. S. Environmental Protection Agency advises
that steps be taken to reduce radon levels in the home if the levels are above 4
picocuries per liter of air (pCi/l). Short and long term radon test kits are available
to the public at minimal cost from the Environmental Affairs Department. A Radon
Specialist is also available to answer questions about radon and to assist the public
in obtaining the proper type and number of test kits for his/her particular home
or building. For information call (336) 703-2440 and state that you have a radon
question/problem.
ENVIRONMENTAL TOBACCO SMOKE (ETS)
ETS is a complex mixture of over 4700 chemical compounds, including
gases and particles, from incompletely burned tobacco.
Sources
Environmental tobacco smoke is the secondhand smoke exhaled by smokers and the sidestream
smoke from the burning of cigarettes, cigars, and pipes.
Health Effects
According to the USEPA, short term exposure to ETS can irritate the eyes, nose,
and throat. Long-term exposure can cause respiratory problems, such as wheezing,
bronchitis, pneumonia, and lung cancer. Asthma attacks may be precipitated by respiratory
irritation or infections related to ETS exposure.
Control Methods
ETS can be totally removed from indoor air only by removing the source: cigarette,
cigar, and pipe smoking. A separate smoking area, mechanical ventilation, or air
cleaners may reduce, but will not eliminate non-smokers exposure to ETS.
LEAD
Lead is a naturally occurring soft metal that was once widely used in gasoline,
paint, and plumbing fixtures. Lead was used in house paint until 1978 when it was
banned. Lead solder for pipes was also banned, but there are plenty of older homes
with these high lead materials still in them.
Sources
Lead
can be found in paint, dust, soil, and water. Lead poisoning in homes most commonly
occurs when a child eats paint chips, sucks on lead-dusted hands and toys, or chews
on lead painted window sills and stair rails. In most cases lead based paint in
good condition is not a hazard. In most cases, older homes have been painted multiple
times resulting in the older lead based paint being covered several times and therefore,
less of a hazard. Renovation and home remodeling projects should take lead paint
into consideration especially if sanding or sand-blasting of paint is being planned.
Sanding and sand-blasting of lead based paint can emit lead dust into the air and
create a hazard. Drinking water may also contain lead from old pipes or solder,
particularly if the water is soft, corrosive, or acidic. The longer water stands
in pipes, the greater the possibility of lead being dissolved in it. Other potential
sources of lead exposure include hobbies (such as working with stained glass), food
and liquids stored in lead crystal, lead-glazed pottery or porcelain, and indoor
target ranges.
Health Effects
Some health effects associated with exposure to lead include nerve and brain damage,
anemia, kidney damage, and growth retardation. All children up to six years old
should be tested for lead poisoning if their doctors think they are at risk. Children
are at a higher risk from lead exposure because they put their hands in their mouth,
their growing bodies absorb more lead, and their brains and nervous systems are
more sensitive to the damaging effects of lead. If lead gets into a child’s body,
it could cause a lower IQ, kidney damage, hearing loss, headaches, slowed growth,
anemia, or behavior problems.
Control Methods
Deteriorating paint or high levels of dust can pose a hazard in homes with lead
paint. Paint chips should be cleaned up immediately and excessive dust should be
cleaned regularly. Paint suspected to contain high levels of lead should not be
removed by dry scraping, belt-sanding, propane torch, or heat gun because these
actions generate large amounts of dust and fumes.
ASBESTOS
Asbestos is a name given to a group of naturally occurring minerals found throughout
the world. The asbestos mineral is composed of bundles of fibers that are very durable,
heat resistant, and noise absorbing. Asbestos products have proven to be very resilient
and have been used in building products since the late 1800’s. In 1971 asbestos
was declared unsafe and listed as a hazardous air pollutant by the United Stated
Environmental Protection Agency. Asbestos have proven to be superior over other
materials as long as it remained intact. When asbestos is disturbed and becomes
air-borne and an individual inhales it severe health problems could result.
Sources
Asbestos
has been banned from some products and voluntarily removed from others but still
remains in thousands of products, homes, and buildings. It is also still being used
in some products being manufactured today. Asbestos is common in buildings built
prior to 1980 and can be found in buildings built beyond 1980. Asbestos has been
used in pipe and boiler insulation, floor tile and floor coverings, ceiling materials
including sprayed on texturing and tiles, and roofing and cementous products. Most
times asbestos can be in a product and can not be determined by sight.
Health Effects
Health effects resulting from exposure to asbestos depend on many factors. Normally
the greater the exposure, the greater the chance of getting an asbestos-related
disease. Most health effects related to asbestos also have a latency period meaning
that health problem from exposure to asbestos have a delayed effect and may not
appear for fifteen to forty years.
Control Methods
Asbestos materials are not a hazard unless they are in a condition where the fibers
can become air-borne. If asbestos is in a product such as flooring that is in good
condition there is no need to remove it. If not done properly, replacing the asbestos
flooring can be a bigger hazard than if it was left intact on the floor. Asbestos
does not have to be removed but if it is, it should be handled properly by someone
trained to work with it.
MOLD
Molds
are a part of our natural environment. They are forms of fungi (microscopic organisms),
grow year round, and can be found indoors and out. Outdoors they can be found in
shady, damp areas or places where leaves or other vegetation is decomposing. Indoors
they can be found where humidity levels are high such as basements or showers. Mold
will grow and multiply under the right conditions, needing only sufficient moisture
(example: in the form of very high humidity, condensation, or water from a leaking
pipe, etc.) and the right material to grow on. Mold growth is encouraged by warm
and humid conditions, although it can grow during cold weather. There are thousands
of species of mold and they can be any color. Molds may be gray, black, green, yellow,
orange, or various other colors and may have a velvety or wooly structure. Molds
produce tiny spores in order to reproduce. Mold spores continually sift through
the air, both indoors and out. When they land on a damp spot they may begin growing
and digesting whatever they are growing on in order to survive. Indoors, molds tend
to grow on porous materials such as wood, sheet rock, insulation, paper, fabrics,
carpet, foods, and other organic materials. Molds gradually destroy some things
they grow on.
View/Print our Mold Brochure
Sources
Mold growth will occur if there is sufficient moisture. Common sources of moisture
include:
- Flooding
- Roof leaks
- Humidifiers
- Plumbing leaks
- Drainage problems
- Damp basements & crawl spaces
- Steam from the bathroom or kitchen
- Condensation from a heating/AC unit
- Poor or improper ventilation of combustion appliances
- Condensation resulting from poor or improper insulation or ventilation
Indications of a moisture problem may include discoloration of the ceiling or walls,
warping of the floor, or condensation on the walls or windows. The key to preventing
mold growth is to control moisture problems.
Health Effects
Exposure to mold can cause health effects in some people. Some people are sensitive
to mold and if they inhale or touch mold certain allergic reactions can result.
Symptoms such as nasal stuffiness, headaches, throat or eye irritation, coughing
or wheezing, or skin irritation may occur. More severe reactions may include fever
and shortness of breath. Molds can also trigger asthma episodes in sensitive asthmatics.
Control Methods
The control of moisture and humidity is the key to controlling mold.
- When water leaks or spills occur indoors, ACT QUICKLY.
- If wet or damp materials or areas are dried up 24 – 48 hours after a leak
or spill occurs, in most cases mold will not grow.
- Wet carpets should be rolled back and allowed to dry completely.
- Air conditioning drip pans should remain clean and the drain lines unobstructed
and flowing properly.
- The ground should slope away from the building foundation so the water does not
enter or collect around the foundation or flow into the crawl space or basement.
- Indoor humidity should be kept low, if possible below 60 per cent.
- If condensation or moisture is observed collecting on windows or walls the wet surface
should be dried and the water source reduced. Condensation can be a sign of high
humidity.
- Appliances that produce moisture should be vented. Clothes dryers, stoves, kerosene
heaters should be vented to the outside when possible. These appliances produce
water vapor and will increase humidity unless vented to the outside.
- Run the bathroom fan or open the window when showering.